Wednesday, July 20, 2011

Coolant sensor

What does the coolant sensor do: Its usually fitted at the cylinder head, some cars can have more then one sensor. The coolant sensor is used to monitor the temperature of the engine coolant inside the engine. The sensor showes the temperature in a resistance change as it does in proportion between colder to warmer coolant. Input from the coolant sensor tells the computer when the engine is warm so the ECU can change the opening time of the injectors and they function. It uses the coolant temperature to know when to run rich or lean the engine needs to be according the engine temperature.
Cooland sensor diagnosis: A visual inspection of the coolant sensor will sometimes have a problem such as corrosion around the terminal, a crack in the sensor or coolant leaks around the sensor. But in the most cases, the only way to know if the coolant sensor is good or bad is to measure its resistance and voltahe reading. The internal resistance of the coolant sensor can be measured and checked with an ohmmeter and compared to the specification. If the sensor is open, shorted or reads out of range, it must be replaced by a new one as there is a fault in it or at the wiring.
Coolant sensor voltage checks: You can also use a voltmeter to check the sensors output. Specs vary on the sensors and brands, but normally a cold coolant sensor will show something around 3 volts. As the engine warms up, and reaches operating temperature, the voltage drop should go down to 1.2-0.5 volts. Best to start the engine and wait for 5 minutes, it will reach its operating temperature.

Oxygen Sensor


What does the oxygen O2 Sensor do:
 It is the primary measurement device for the fuel control computer in your car to know if the engine is too rich or too lean. The O2 sensor is active anytime it is hot enough, but the computer only uses this information in the closed loop mode. Closed loop is the operating mode where all engine control sensors including the Oxygen sensor are used to get best fuel economy, lowest emissions, and good power. If the Oxygen sensor will be faulty, the fuel economy and emissions will change to the bad side and the engine will start fine but on idle it will be rough can even shut down and stop working.
Oxygen sensor diagnosis: You can plug in a sensor diagnosis tool and the the voltage its working. It must change really often and fast, if it does that really slow and not good enough. Then the sensor is old or getting old and started to be lazy and it needs to be replaced by the same new one. The is alot od different types of sensors and wirings. So you should be sure they are the same. Oxygen sensors needs to be changed at around 80000km on the car as by that time they are getting old, some sensors can even last a life time of the car but it depends how good is the engine and if it had any problems before.

Petrol Fuel Injector Testing



In this test first of all I did a listening test. I heard the injector with a long screwdriver. They must have a sharp tap and not a dull thud. They sounded proper and thus they were ok.

CHECK VOLTAGE
Then I did the voltage test. I checked the voltage across the battery first and then checked the voltage across the injectors one by one. The voltage across the battery was 13.1V and across each injector starting from first cylinder were 13.4V, 13.5V, 13.5V, 13.5V. The readings were all right.
LED TEST
Then I did a test using a LED tester. I connected the LED tester to the battery and connect tip to pin that has back probed connector to injector. As the injector is grounded by the ECM to fire, the test light should also be grounded to fire, and will flash. I did it one by one on each of the injector. And every injector was flashing the light. So they all passed the LED test.

DUTY CYCLE TEST
After that I used a multimeter and set it to duty cycle and watched injector firing when the engine was idling. I read at each one of the injectors one by one. The readings were as follows:-
       Cyl 1: 4.9%       Cyl2: 4.6%   Cyl 3: 4.6%    Cyl 4: 4.9%


In the next test I did the same test but the engine was accelerating. The readings were as follows:-
      Cyl 1: 18.5%     Cyl 2: 18.3%    Cyl 3: 22.3%     Cylr 4: 18.6%

HZ TEST
Then I set the meter on Hz. Then with the engine was idling then I took reading on each cylinder.
     Cyl 1: .007   Cyl2: .006   Cyl 3: .006   Cyl 4: .007

Then I did this test again with the engine revving. The readings changed and were as follows:-
 Cyl 1: .025  Cyl 2: .018  Cyl 3: .021   Cyl 4: .030

PULSE WIDTH
Then I calculated the pulse width using the formula
Pulse width ms = (% Duty Cycle * 100)/ Frequency
Then the pulse width when the engine was idling then the pulse width was as follows:-
   Cyl 1: 70 Cyl 2: 76.676  Cyl 3: 76.676    Cyl 4: 70

Then pulse width when the engine was revving
 Cyl 1: 74   Cyl 2: 101.667   Cyl 3: 106.19   Cyl 4: 62

REFLECTIONS
I think the way I tested the injector was quiet a suitable way of checking any faults in it. The reason of all the tests showed a posetive rsult and which is supposed to be.

Scan Tool Diagnosics


1. Scan Tool Data

        1.1Find a vehicle which is appropriate for the scan tool.

        1.2 Connect the scanner, power it on, follow the instructions and input the correct vehicle information it asks for so you can view the data.

        1.3 Find the data for the information listed on the next page. Turn engine on to idle. Fill in the letters used to label the information and the value of that data. (For example, engine load information may be found under MAP, with a value of 3.6, listed in volts) Note: not all vehicles will support all information, just find as much as you can. If the engine won’t run, input the information with the key on, engine off.


Type of information (PID = Parameter Identification)

Letters to describe it
E.g. TPS
Value of data
Units for data
E.g. volts
Engine Load (how much air comes in)
Intake
15%
Percentage
Engine RPM


RPM

725
Revolutions per minute
Throttle angle


TPS

0.96v

Voltage
Engine coolant temperature
ECT
33°C
Degree Celsius
Intake air temperature
IAT
3.73

Fuel Injection opening pulse

FIOP
4.71
Ms
Transmission select position
-


Vehicle Speed


-

0

KM/H
Oxygen sensor(s)


O2

0.10-0.70v

Voltage
Fuel Trim


-


Idle control


IAC

43%

Percentage
Power steering Load

0.02v
Voltage
Air conditioning condition
AC
3.91
Voltage
Exhaust Gas Recirculation (EGR)




Fuel Evap or Purge condition



Malfunction Indicator Light (MIL)



Barometric Pressure



78

Hz











2             Trouble Codes or Fault Codes


2.1       Find where the Codes are listed

 

2.2       Record any codes, and what system and condition they describe in the chart below (Example: might be code number 21, for Throttle Position Sensor, signal voltage too low) If there are no codes listed, put “none”.


3             Lecturer put in Fault

3.1               Find your lecturer and have him create a fault under the hood (don’t look)



4             Record New Codes

4.1       Look up the codes now in the scan tool
4.2       Record the codes in the chart below. Also record what system is affected, and what condition is described.

Code number


System affected
Condition described

PO113

Intake Air temp

High Input

PO100

MAP

High Input

PO122

TPS

Low Input




5             Find What Data Has Changed

5.1       Look through the scan tool data to see what PIDs (Parameter Identification of system voltages) have changed. Which readings don’t make sense or don’t read what you would expect. Concentrate on the PIDs related to the codes.
5.2       Record the PIDs that have changed below:

Type of information (PID = Parameter Identification)

Letters to describe it
Value of data
Units for data

Throttle Position Sensor

TPS

0v

Volts

Intake Air Temp

IAC

15°C

4.98

Engine Speed

RPM

825

RPM






6             Visual Inspection to find fault

6.1       Do a visual inspection under the hood to find where the problem is. Use information from the code to know where to look for the problem and what type of problem to look for.
Describe problem you found:

When the vacuum sensor is disconneted, the engine stops running.


7             Repair fault

7.1       Plug back in the connector, or repair problem found
7.2       Describe what you did:

Air Temp - 28°C  3.03v
TPS= 0.96v


8             Recheck Data PIDs
8.1       Recheck the data with the scan tool
8.2       Record the voltages for the PIDs related to the problem, to confirm they are back to normal

Type of information (PID = Parameter Identification)

Letters to describe it
Value of data
Units for data

Engine Speed

RPM

825

RPM

Coolant Tempurature Sensor

CTS

90

℃

Throttle Position Sensor

TPS

0
Volts

Intake Air Temp

IAC

15°C

4.98

9             Clear Codes 
Describe what you did to clear codes:
         
           I disconnected of the negative terminal  off the battery and took out  the engine main fuse for 30 seconds

10         Recheck for codes and record codes in system now:
         
 I rechecked the codes by selecting D.T.C, and there was no trouble codes on the screen.        

11      Discuss the importance live data when fault finding
It shows the state of the sensors from the live data values

12      Explain the need for parameters when checking live data
        
          when the fault is resolved, the live data will be rechecked with its parameters then the data should be compared to fault datas.




13     Discuss how a scan tool can aid you when fault finding
         
  I can find the fault easily now and although the vehicle is old or new, I can also check the state of a vehicle with various information.