Wednesday, July 20, 2011

Scan Tool Diagnosics


1. Scan Tool Data

        1.1Find a vehicle which is appropriate for the scan tool.

        1.2 Connect the scanner, power it on, follow the instructions and input the correct vehicle information it asks for so you can view the data.

        1.3 Find the data for the information listed on the next page. Turn engine on to idle. Fill in the letters used to label the information and the value of that data. (For example, engine load information may be found under MAP, with a value of 3.6, listed in volts) Note: not all vehicles will support all information, just find as much as you can. If the engine won’t run, input the information with the key on, engine off.


Type of information (PID = Parameter Identification)

Letters to describe it
E.g. TPS
Value of data
Units for data
E.g. volts
Engine Load (how much air comes in)
Intake
15%
Percentage
Engine RPM


RPM

725
Revolutions per minute
Throttle angle


TPS

0.96v

Voltage
Engine coolant temperature
ECT
33°C
Degree Celsius
Intake air temperature
IAT
3.73

Fuel Injection opening pulse

FIOP
4.71
Ms
Transmission select position
-


Vehicle Speed


-

0

KM/H
Oxygen sensor(s)


O2

0.10-0.70v

Voltage
Fuel Trim


-


Idle control


IAC

43%

Percentage
Power steering Load

0.02v
Voltage
Air conditioning condition
AC
3.91
Voltage
Exhaust Gas Recirculation (EGR)




Fuel Evap or Purge condition



Malfunction Indicator Light (MIL)



Barometric Pressure



78

Hz











2             Trouble Codes or Fault Codes


2.1       Find where the Codes are listed

 

2.2       Record any codes, and what system and condition they describe in the chart below (Example: might be code number 21, for Throttle Position Sensor, signal voltage too low) If there are no codes listed, put “none”.


3             Lecturer put in Fault

3.1               Find your lecturer and have him create a fault under the hood (don’t look)



4             Record New Codes

4.1       Look up the codes now in the scan tool
4.2       Record the codes in the chart below. Also record what system is affected, and what condition is described.

Code number


System affected
Condition described

PO113

Intake Air temp

High Input

PO100

MAP

High Input

PO122

TPS

Low Input




5             Find What Data Has Changed

5.1       Look through the scan tool data to see what PIDs (Parameter Identification of system voltages) have changed. Which readings don’t make sense or don’t read what you would expect. Concentrate on the PIDs related to the codes.
5.2       Record the PIDs that have changed below:

Type of information (PID = Parameter Identification)

Letters to describe it
Value of data
Units for data

Throttle Position Sensor

TPS

0v

Volts

Intake Air Temp

IAC

15°C

4.98

Engine Speed

RPM

825

RPM






6             Visual Inspection to find fault

6.1       Do a visual inspection under the hood to find where the problem is. Use information from the code to know where to look for the problem and what type of problem to look for.
Describe problem you found:

When the vacuum sensor is disconneted, the engine stops running.


7             Repair fault

7.1       Plug back in the connector, or repair problem found
7.2       Describe what you did:

Air Temp - 28°C  3.03v
TPS= 0.96v


8             Recheck Data PIDs
8.1       Recheck the data with the scan tool
8.2       Record the voltages for the PIDs related to the problem, to confirm they are back to normal

Type of information (PID = Parameter Identification)

Letters to describe it
Value of data
Units for data

Engine Speed

RPM

825

RPM

Coolant Tempurature Sensor

CTS

90

℃

Throttle Position Sensor

TPS

0
Volts

Intake Air Temp

IAC

15°C

4.98

9             Clear Codes 
Describe what you did to clear codes:
         
           I disconnected of the negative terminal  off the battery and took out  the engine main fuse for 30 seconds

10         Recheck for codes and record codes in system now:
         
 I rechecked the codes by selecting D.T.C, and there was no trouble codes on the screen.        

11      Discuss the importance live data when fault finding
It shows the state of the sensors from the live data values

12      Explain the need for parameters when checking live data
        
          when the fault is resolved, the live data will be rechecked with its parameters then the data should be compared to fault datas.




13     Discuss how a scan tool can aid you when fault finding
         
  I can find the fault easily now and although the vehicle is old or new, I can also check the state of a vehicle with various information. 

WS7 Exhaust Gas Analysis

WS7 Exhaust Gas Analysis ( Petrol only)

Exhaust Analyser should be warmed up and recently calibrated. When it’s time to start taking tailpipe readings, put the analyser probe into the tailpipe and install exhaust tube over probe to capture exhaust fumes. Make sure there is adequate ventilation.

Note: make sure you fill out the “means: .............  segment to explain what that gas reading means. Example, if you are measuring HC, which shows us about misfire in the engine, and you had a low number like 28 ppm, you would say “shows low amount of misfire”, or “most of the fuel is being burnt.” But if the HC was high, like 340 ppm, you might say “There is a high amount of misfire” or “not all the fuel is being burnt.”





            With the analyser probe sensing normal air, what are the Four Gas readings? Record the amount and then what it means:

CO 0.001    means: Rich conditions and not enough of O2
HC 12ppm  means:  HC ramains the hole burn fuel and if the hc is high, that means there is ubrurned guel in the gases. CO2 0.00% means:Efficency
O2 20.90   means:  That it is lean


2)        Start the engine idling cold, and record the Four Gas readings
Explain what is happening within the engine referring to the four gases:    

CO 2.5% 
 HC 788 
 CO2 12.6 
 O2 5.15. 
When the engine starts  cold , the CO increase to 2.5%. This means that rich mixture enters the combustion chamber. The HC also goes up significantly and unburn fuel remains in the exhaust gases. The CO2 (efficency) is low and the O2 is high from the inactive catalytic converter.  

        
3)    When the engine has warmed up, record the Four Gas readings:
Explain what is happening within the engine referring to the four gases:      

CO 0.58 
 HC 235 
 CO2 14.2 
 O2 1.10 
When the engine is warmed up, the CO & HC decrease. This means that the ideal mixture enters the combustion chamber. The CO2(efficency) is high and the O2 is low because the catalytic conver well operates for cleaning the emissions.

4)    Run the warm engine at 2500 RPM, record the Four Gas readings:
Explain what is happening within the engine referring to the four gases:      

CO 2.5  
HC 434 
CO2 10% 
 O2 1.3 
When the engine is running warm at 2500 rpm, the CO and HC are more produced than the engine idling due to higher RPM with more emissions. However, the CO2 and O2 are still similar to idling condition.
5)         At idle, run the mixture rich with extra propane, LPG, or carburettor cleaner,  and record the Four Gas readings:
Explain what is happening within the engine referring to the four gases:      

CO 0.96
  HC 224pmm
 CO2 225
  O2 1.08 
 At idle,we had disconnected the vacuum hose in the fuel regulator for the rich condition. The CO increases to 0.96 which means the state of rich mixture. The unburn fuel is more produced due to more fuel injection.  







6)    At idle, create a lean condition with an air leak or vacuum leak, record the Four Gas readings:       
    Explain what is happening within the engine referring to the four gases:        

CO 0.069 
 HC 736 
 CO2 16.75  
O2 11.30. 
At idle, We disconnected  the PCV valve for the lean condition. The CO recovers the nomal condition. The unburn fuel goes up at 470ppm. The CO2(efficency) is reduced but the O2 increases significantly which means the state of lean mixture. 


7)   Accelerate the engine, by blipping the throttle a few times (don’t rev too high anddamage the engine), and watch how the gas readings change.  Record the Four Gas readings when the CO is highest: 
    Explain what is happening within the engine referring to the four gases:        

CO 2.547
 HC 699
CO2 10.54
  O2 2.52
 
From the sudden acceleration, the rich mixture is supplied into the combustion chamber. The CO and HC rise. The CO2(efficency) is reduced but the O2 increases slightly due to more fuel injection with more intake air.  


8)    Disconnect one spark plug wire, ground it with a jumper wire, then record the Four Gas readings as the engine idles:
     Explain what is happening within the engine referring to the four gases:       

CO 0.01 
 HC 10.33 
CO2 13.6  
O2 453 
When the misfire is produced in a cylinder, the HC increases dramatically because the unburn fuel is created by the misfired cylinder. The O2 is also produced more from the air/fuel mixture of the misfired cylinder.

9)    If you can get to it, disconnect the injector harness connector from one injector on an engine that has one injector for every cylinder: Record the Four Gas readings as the engine idles:
Explain what is happening within the engine referring to the four gases:      

CO 0.047
  HC 225 
CO2 12.09 
 O2 4.75 

When the injector is disconnected, the HC is normal because the fuel does not injects into the intake port. However, the O2 increases due to the air is still supplied into the combustion chamber

10) Optional: Make other changes to the engine at idle, such as turning on the air conditioning or rocking the steering wheel.  Note the change you made: 
    Explain what is happening within the engine referring to the four gases:        

CO 0.049 
 HC 74
  CO2 15.34 
 O2 0.12

Overall, the emission is clean with proper values. However, when loads (air conditioning and rocking the steering wheel) are added, the rpm will go up. As a result , the CO and HC increase slightly with the rich condition.  

Return the vehicle to good condition and proper adjustment.

11)      Explain the different readings you would get from a vehicle with a catalytic converter and a vehicle without one and why?

I would get the differnt readings. If the vehicle does not have a catalytic converter the emission will be exhausted without any filtering. The catalytic converter helps reducing emissions with its chemical actions.


12)      Explain what light off point means and what happens?

 When the temperature is hot enough, the catalytic converter will clean the emissions with its operating temperature.



13)       On lambda, 02 sensors why do they have 1,2,3,4 or 5 wires and what do these extra wires do?

From two white heater positive and negative, the O2 sensor works correctly and increases responses with operating temperature when the engine starts with cold conditions. The black wire is a snesor signal positive which gives the state of exhaust gases to the ECU. The gray wire is a sensor signal earth