Wednesday, July 20, 2011

Throttle Position Sensor




THEORY
The throttle position switch is operated by the throttle. It has a set of contacts for both idle and full-throttle positions. The switch signals the throttle opening to the ECU, which provides mixture correction for both idle and off idle as well as full throttle conditions. These switches became a variable resistor potentiometer type in later systems. The engine ECU using a potentiometer TPS receives an analogue voltage signal that varies with throttle position. The advantage of this design is the ECU can determine the exact position of the throttle valve at any instant and can also see the rate of the driver’s throttle application.



PROCESS
In this I checked the voltage across the sensor I connected the voltmeter across the sensor the voltage was found to be 0.7V when the throttle was closed and it was 1V when the throttle was open.

REFLECTIONS
The throttle position sensor gives a reading which tells the ECU that how much fuel should be provided. The TPS gives less voltage when the throttle is closed as the throttle opens it increases the voltage. It tells the ECU how much fuel is required to be injected.

Fuel Pressure and flow

.         Locate the two closest fire extinguishers.  (If you have to use it remember to pull the pin, squeeze the handle, and spray at the base of the flame.) Write down where they are:
              Front left of the room
2.         If you can, look up Fuel Pressure specifications for the vehicle you are testing. If you can’t look them up, make a guess at the fuel specs you should have and write them down here:
                   38-44psi
3.         Use eye protection. Optional: Relieve fuel pressure before installing pressure gauge. Or there will be some fuel that sprays at you as you attach the gauge. You can relieve pressure by several methods: 1) To relieve the fuel pressure. Make sure you have a rag to catch the fuel, start the engine. 2) Remove fuel pump (circuit opening) relay or fuse and run the engine until it stops, then crank to check that the engine doesn’t start 3) Use a vacuum gauge on the pressure regulator to lower fuel pressure, or  4) Open a fuel line at some pressure point and catch the fuel in a rag beware there may be lots of fuel.

4.         Attach fuel pressure gauge and notice which scale on the gauge you will be using. Briefly turn key on or start vehicle, then turn it off. Check for fuel leaks.
Are there leaks? Yes ...................... No ✓
If there are leaks you must correct them and retest before continuing.
5.         Measure the fuel pressure with the key on, engine off.
Record it here: 40psi
6.         Idling: Measure the fuel pressure with the engine idling. Watch the pressure for a couple of minutes.
Record pressure here: 41psi
7.         Maximum: With the engine idling, use the special tool to clamp the fuel return line. Note: this can only be done for a short period.                                                            
Record pressure here: 75psi
8.         WOT: With the engine idling, disconnect and plug the vacuum linegoing to the fuel pressure regulator.
          Record pressure here: 48psi
9.         Residual: Turn off the engine, and watch the fuel pressure for five minutes.
Record your residual or rest pressure here: 42.5psi

10.      Flow: Hook up proper equipment to read fuel volume if necessary. Record flow gauge results of volume, or how much pumped in 15 seconds: (normal results may be ½ liter in 15 seconds)
                                666ml

11.      Replace vacuum lines. Carefully remove the fuel pressure gauge (beware of fuel spraying into eyes, avoid sparks, etc.) Turn engine key on and off, check for leaks.  Start engine, check for leaks. No leaks? Check here: ✓Replace cap over fuel pressure test port. Check when done: ✓Make sure the vehicle is safe and runs fine when done, or tell your instructor.

12.      Explain why it is important to know a vehicle fuel pressure/flow?

To make sure it is running at its maximum capacity


13.      Describe the symptoms a vehicle would give with each case

Low fuel pressure

It will run lean , it wont idle properly. RPM will be low and it will be running rough

Low fuel flow

Blocked fuel filter , weak return vavle in pump , sping cam gets weaker it will always be richer , which means it will use alot of fuel

High fuel pressure

Too much fuel being used , dripping injectors means that there will be flooding , return regulator will be broken.
Faulty fuel pressure regulator

Floading of injectors which will leak out. The injectors causes hard starting , poor economy and useing more fuel

Camshaft Sensor

CAMSHAFT SENSOR 




THEORY
As the engine management systems developed, newer processes like sequential fuel injection and variable camshaft timing was adopted. For these developments to operate the engine ECU had to calculate events on more than just crankshaft position. For sequential fuel injection the ECU had to know not only crank angle, but it had to know which if the four strokes the piston was on. Also, with the advent of variable camshaft and valve timing, the engine ECU had to be able to read the relative position of the camshaft, in relation to the crankshaft, to determine the exact dynamic cam timing. The sensors are mounted on one or more camshafts or in a camshaft-driven distributor. These sensors are usually hall effect devices, optical triggers or inductive pickup.

PROCESS
In this I checked the voltage across the cam sensor. I put the voltmeter on ac volts. Then I measured the voltage at Idle rpm and at 2500 rpm. The voltage would around 0.3V at Idle and 0.5V at 2500 rpm.

REFLECTION
The voltage reading was under the spec hence the cam sensor is working properly.

Flash Codes ( Engine Check Light )


In this task we created some faults on one of the sensors and then tried to find the codes using the flash codes. The ECU would log that there is a fault with the engine. The flash code test can be done only on EFI cars not on the ones with carburettors


Flash code is a fault that is stored in the ECU and when there is a fault in a specific sensor it flashes a specific number which tells us which of the sensors have a fault. You can then bring up the code by. Turning the engine off, then turn the key to ignition then off, then switch it to ignition again, then off, then bring it to ignition again; the codes will begin to flash on the check engine light. The sequence in which the light will flash is it will flash out first number to its value.
Most of the times the fault has to be corrected by replacing the sensor but sometimes it are also due to some loose wires. The ECU can only tell which sensor has a fault but cannot tell that weather the fault is in wiring or in the sensor itself and thus diagnostics could be difficult because of this.

To clear the faults you have to remove the battery negative terminal for 30 seconds as this will clear the ECU memory. Then start the engine on and if the light does not come over then the fault has been cleared successfully. 

Coolant sensor

What does the coolant sensor do: Its usually fitted at the cylinder head, some cars can have more then one sensor. The coolant sensor is used to monitor the temperature of the engine coolant inside the engine. The sensor showes the temperature in a resistance change as it does in proportion between colder to warmer coolant. Input from the coolant sensor tells the computer when the engine is warm so the ECU can change the opening time of the injectors and they function. It uses the coolant temperature to know when to run rich or lean the engine needs to be according the engine temperature.
Cooland sensor diagnosis: A visual inspection of the coolant sensor will sometimes have a problem such as corrosion around the terminal, a crack in the sensor or coolant leaks around the sensor. But in the most cases, the only way to know if the coolant sensor is good or bad is to measure its resistance and voltahe reading. The internal resistance of the coolant sensor can be measured and checked with an ohmmeter and compared to the specification. If the sensor is open, shorted or reads out of range, it must be replaced by a new one as there is a fault in it or at the wiring.
Coolant sensor voltage checks: You can also use a voltmeter to check the sensors output. Specs vary on the sensors and brands, but normally a cold coolant sensor will show something around 3 volts. As the engine warms up, and reaches operating temperature, the voltage drop should go down to 1.2-0.5 volts. Best to start the engine and wait for 5 minutes, it will reach its operating temperature.

Oxygen Sensor


What does the oxygen O2 Sensor do:
 It is the primary measurement device for the fuel control computer in your car to know if the engine is too rich or too lean. The O2 sensor is active anytime it is hot enough, but the computer only uses this information in the closed loop mode. Closed loop is the operating mode where all engine control sensors including the Oxygen sensor are used to get best fuel economy, lowest emissions, and good power. If the Oxygen sensor will be faulty, the fuel economy and emissions will change to the bad side and the engine will start fine but on idle it will be rough can even shut down and stop working.
Oxygen sensor diagnosis: You can plug in a sensor diagnosis tool and the the voltage its working. It must change really often and fast, if it does that really slow and not good enough. Then the sensor is old or getting old and started to be lazy and it needs to be replaced by the same new one. The is alot od different types of sensors and wirings. So you should be sure they are the same. Oxygen sensors needs to be changed at around 80000km on the car as by that time they are getting old, some sensors can even last a life time of the car but it depends how good is the engine and if it had any problems before.

Petrol Fuel Injector Testing



In this test first of all I did a listening test. I heard the injector with a long screwdriver. They must have a sharp tap and not a dull thud. They sounded proper and thus they were ok.

CHECK VOLTAGE
Then I did the voltage test. I checked the voltage across the battery first and then checked the voltage across the injectors one by one. The voltage across the battery was 13.1V and across each injector starting from first cylinder were 13.4V, 13.5V, 13.5V, 13.5V. The readings were all right.
LED TEST
Then I did a test using a LED tester. I connected the LED tester to the battery and connect tip to pin that has back probed connector to injector. As the injector is grounded by the ECM to fire, the test light should also be grounded to fire, and will flash. I did it one by one on each of the injector. And every injector was flashing the light. So they all passed the LED test.

DUTY CYCLE TEST
After that I used a multimeter and set it to duty cycle and watched injector firing when the engine was idling. I read at each one of the injectors one by one. The readings were as follows:-
       Cyl 1: 4.9%       Cyl2: 4.6%   Cyl 3: 4.6%    Cyl 4: 4.9%


In the next test I did the same test but the engine was accelerating. The readings were as follows:-
      Cyl 1: 18.5%     Cyl 2: 18.3%    Cyl 3: 22.3%     Cylr 4: 18.6%

HZ TEST
Then I set the meter on Hz. Then with the engine was idling then I took reading on each cylinder.
     Cyl 1: .007   Cyl2: .006   Cyl 3: .006   Cyl 4: .007

Then I did this test again with the engine revving. The readings changed and were as follows:-
 Cyl 1: .025  Cyl 2: .018  Cyl 3: .021   Cyl 4: .030

PULSE WIDTH
Then I calculated the pulse width using the formula
Pulse width ms = (% Duty Cycle * 100)/ Frequency
Then the pulse width when the engine was idling then the pulse width was as follows:-
   Cyl 1: 70 Cyl 2: 76.676  Cyl 3: 76.676    Cyl 4: 70

Then pulse width when the engine was revving
 Cyl 1: 74   Cyl 2: 101.667   Cyl 3: 106.19   Cyl 4: 62

REFLECTIONS
I think the way I tested the injector was quiet a suitable way of checking any faults in it. The reason of all the tests showed a posetive rsult and which is supposed to be.